CONTACT US:   Send an Email      (706) 398-1178      (706) 398-1188      1451 Scenic Hwy, Rising Fawn, GA 30738

General Considerations

1.0 SCOPE

The purpose of this procedure is to establish a general welding procedure for the repair of some casting components of Vulcan Foundation Equipment Inc. hammers. It will cover only the fundamental parameters of the welding process. The welding techniques are well established and generally standardized.

2.0 QUALIFICATION

It is recommended that welding operators be certified in accordance with the requirements of Section IX of the ASME Boiler Code or ASTM A-488. Performance Qualification of Welders under these documents is simple, testing the ability of the welder to produce a “sound” weld in small carbon-steel plate.

3.0 THE WELDING PROCESS

There are many welding processes available today, from completely automatic “electroslag” processes to semi- automatic “Metal-Inert-Gas” (MIG) process. In this procedure only one process will be considered; the “Shielded-Metal-Arc- Welding” (SMAW) process. This is the oldest, simplest and most versatile process available today.

3.1 Welding Current

The current for the SMAW process is usually DC Positive (Reverse Polarity). Any type of welding current generators may be used. Most welding machines have “rectifiers” with a capacity of at least 400 amps and a 100% duty-cycle.

3.2 Electrodes

Only low-hydrogen electrodes should be used for this process. In the AWS-ASTM Classification the approved electrodes would be: EXX15, EXX16, and EXX18. It is important to keep these electrodes moisture-free after removing from the container. They should be stored in an oven at 250° F (120° C) and used within one (1) hour after removal. The absorption of moisture in the electrode coating will result in hydrogen pick-up in the weld deposit and likely produce cracking.

3.3 Techniques

Standard welding techniques are used in this procedure. The bead should be of the “stringer” type. Heat input should always be kept as low as is practical. The welding pass sequence should be selected with the idea of keeping welding stresses to a minimum. This can be done by controlling the heating and cooling rate of the process. The welding sequence passes should be separated as much as is practical; the interpass should be kept low by the use of small-diameter electrodes and low welding current.

4.0 WELDING PARAMETERS

The keys to high quality welding can be summarized in three (3) factors: (1) the selection of the proper electrode for the particular base metal to be repaired, (2) the establishment of the correct preheat temperature to (a) maintain a low hardness in the Heat-Affected-Zone (HAZ) and (b) minimize welding stresses, (3) the selection and use of a suitable interpass temperature to reduce the effects of heating and cooling on the components. This is important since post-welding heat treatment is not always practical and thus, excessive hardness and stresses must be minimized by the correct selection of the welding parameters.

4.1 Electrode Selection

The selection of the proper electrode is based on the composition and mechanical properties of the metal to be welded.

The composition of welding electrodes contains the same alloys as the casting; i.e. manganese, nickel, chromium, molybdenum and vanadium. However, the carbon and silicon contents are lower than the base metal. Therefore, the alloy content of the rod must be higher to achieve the same mechanical properties.

Ideally, the composition and mechanical properties of the electrode should match the casting. When this is not possible, it is more important to coordinate the mechanical properties than the composition. This is true of carbon/low alloy steels, but not of corrosion and heat-resisting high- alloy steels.

4.2 Preheat Temperature

The selection of the preheat temperature should be based on three (3) factors, listed in order of importance:

1. Composition and hardenability of the base or parent metal. 2. The feasibility of post welding heat treatment 3. The size and configuration of the part to be welded.

All of these factors require a higher preheat temperature. The preheat can range from 100° F (40° C) for unalloyed steel to 400° F (200° C) for steels of high hardenability. The temperature is always listed as “minimum” and may be higher, if desired. If possible, the entire part should be preheated in a temperature-controlled furnace. Otherwise, localized heating with torches may be used. There are several precautions that must be observed: (1) the heating must be done slowly (100° F) (38° C/hr), (2) the part must be heated throughout the section, (3) the area preheated should be at least 12″ (30 cm) from the edge of the cavity.

The temperature of the part can be checked by use of “Temp- Sticks”, a temperature-sensitive marker that melts at the designated temperature. The temperature of both sides of the part should be checked to insure complete heating throughout the section.

4.3 Interpass Temperature

The interpass temperature is the temperature of the base metal measured 2″ (5cm) from the weld, between weld passes in a multi-pass welding operation. It is always listed as a maximum, and is usually less than 200° F (95°C) above the preheat temperature.

The primary purpose of controlling the interpass temperature is to minimize the welding induced stresses. A reasonable interpass temperature will also prevent the parent metal from becoming so hot that it “anneals” the weld deposit, causing lower hardness and strength.

5.0 POST WELDING HEAT TREATMENT

Heat treatment after welding accomplishes two (2) things: (1) relieves the stresses incurred during welding; (2) reduces the hardness in the HAZ. For these reasons it is advantageous to heat-treat all parts after welding. Unfortunately, this is not always possible.

There have been many attempts to stress-relieve parts without using a heat treating furnace. Most of these methods are ineffective. The amount of stresses relieved is dependent on the temperature of the part and the time at that temperature. Since the temperature of these make-shift operations is usually in the range of 700°-800°F (370-430°C) the holding times would have to be in the 10-12 hour range. These methods are not recommended.

6.0 CHOOSING A WELDING PROCEDURE

The choice of a particular welding procedure is strictly dictated by the material composition of the piece being repaired. As VULCAN FOUNDATION EQUIPMENT INC. is constantly improving its material specifications, it is necessary that the end user of the product or the repair facility doing the welding contact the factory to determine the exact material composition of the particular casting involved.

©2017 Pile Hammer Equipment
Brought To You By: Absolute Synergy Squad, LLC